Best Exam Practice Material for DELL EMC DES-4122 Exam Q&A

Jonnie Karnath2023-03-12T22:18:16+00:00

If you want to reduce your chances of failure and increase your chances of success, consider using DELL EMC DES-4122 exam Q&A to prepare for your Specialist – Implementation Engineer PowerEdge Version 2.0 exam. Certspots DELL EMC DES-4122 exam Q&As are created by industry experts who have years of experience in the field of DELL EMC. The questions are updated regularly to ensure that they reflect the most current trends and technologies in the industry, and to keep up with any changes to the exam format or content. These study materials can help candidates build a solid foundation of knowledge and can help you feel more confident and prepared on the day of the exam.

Page 1 of 2

1. A Dell EMC PowerEdge server has been updated with an LCC and iDRAC DUP to the latest firmware when performing a firmware rollback?

Both the iDRAC and the LCC can be rolled back

The LCC can be rolled back; the iDRAC cannot be rolled back

The iDRAC can be rolled back; the LCC cannot be rolled back

The iDRAC cannot be rolled back and the LCC cannot be rolled back

2. You must configure a BOSS card with 2 x 120GB drives for a Dell EMC PowerEdge server .

What is the only supported mode?

RAID 0

RAID 5

RAID 1

Non-RAID Mirroring

3. CORRECT TEXT

A system engineer has a 14G Dell EMC Poweredge server with an amber light blinking. The engineer must pull a SupportAssist collection before calling Dell Support to evaluate what the potential problem. Use the simulator to collect and view the SupportAssist collection.

4. Which rear disk drive option is available in a Dell EMC PowerEdge R740xd server?

4x 3.5" drives

2x3.5" drives

8x2 5" drives

6x2 5" drives

5. What must be done before upgrading OMSA from the 32-bit to the 64-bit version?

Save the license file

Disable UAC

Back up the configuration

Uninstall the earlier version

6. An engineer needs to install an additional PSU on an existing, single PSU Dell EMC PowerEdge R740. They complete the initial installation and cabling procedures. They connect an AC cable and the power distribution unit produces normal AC output. The engineer checks power management and sees that the new PSU is in the Failed state.

What task should be completed to troubleshoot this issue?

Confirm the System Input Power CAP is not set to Low

Set the PSU AC redundancy to 1+1

Set the PSU AC redundancy to 1+0

Verify the new PSU is the same type and wattage rating

7. What is used by the Lifecycle Controller to directly back up the server profile on a 14G Dell EMC PowerEdge server?

Network share

vFlash SD card

USB Flash drive

IDSDM SD card

8. A technician wants to remotely log in to a server but finds that the IDRAC virtual Console feature Is not available. Use the simulator to explore the system .

What Is the cause of this Issue?

Note: It is necessary to dose (x) the simulator window before you can select a response to this question.

The Virtual Console is disabled

Operating system not installed on remote server

The server has been powered down

There are more than the maximum number of active sessions

9. DRAG DROP

Match each RAID level to its characteristic.

10. What is a valid password option available from the iDRAC9 Unique ID feature?

Encryption Default

Secure Default

Legacy Generated

Randomly Generated

Page 2 of 2

11. How can a technician know whether IDRAC9 System Lockdown mode is enabled?

Lockdown activation message in red box in the iDRAC web GUI Access to LCC is disabled when the server boots

Lockdown activation message in red box in the iDRAC web GUI Access to LCC requires a password when the server boots

Lockdown activation message in yellow box in the iDRAC web GUI Access to LCC is disabled when the server boots

Lockdown activation message in yellow box in the iDRAC web GUI Access to LCC requires a password when the server boots

12. Which card connects to the PCI bus, is physically smaller than a on the system board of a Dell EMC PowerEdge 14G server?

NDC

OCP

PCIe

FPGA

13. What is the drive characteristic of a BOSS M.2 drive in a Dell EMC PowerEdge server?

Single-level cell

Read Intensive

Quad-level cell

Write Intensive

14. After completing a disk rebuild operation, a technician needs to configure the system so that the rebuild process happens faster the expense of slowing users down.

Which setting should be changed?

Rebuild Rate in the BIOS settings

System Profile to Performance in the BIOS settings

System Profile to Performance in the iDRAC GUI

Rebuild Rate in the iDRAC GUI

15. What is required for iDRAC Direct 2.0 to connect with IDRAC9 interfaces such as RACADM and WSMAN?

Wi-Fi connection

NFC connection

Ethernet cable

Micro-AB USB

16. A Dell EMC PowerEdge server logs the following CPU Machine Check error CPU1 IERR.

What action might solve the problem?

Remove flea power

Update the Intel driver

Reseat the IDSDM

Swap the PERC controller

17. A technician is sent on-site to troubleshoot a server that produced an error message during the most recent POST, but then completed the POST and booted to the operating system. The user cannot remember the specific error and no entry was made in the error log relating to this error.

How can the technician find out what the error message was?

Access the Lifecycle Controller and view the last boot cycle video capture entry

Reload the BIOS firmware

Export the Server profile and analyze for any POST errors

Access the iDRAC and view the last boot cycle video capture entry

18. A Dell EMC PowerEdge 14G server uses Intel OPTANE DC Persistent Memory in App Direct mode .

What is the minimum size DIMM supported for this type of memory?

64 GB

128 GB

256 GB

512 GB

Facebook Twitter LinkedIn Google + Email