CIP Level 2 Certification NACE-CIP1-001 Demo Questions

Jonnie Karnath2023-07-26T08:45:11+00:00

The CIP Level 1 NACE-CIP1-001 exam is an industry-recognized certification for coating inspection professionals. Achieving this certification demonstrates knowledge and competency in the field of coatings and corrosion control. For those looking to prepare for the CIP Level 2 Certification NACE-CIP1-001 exam, Certspots offers free NACE-CIP1-001 demo questions to help with exam preparation. These NACE-CIP1-001 demo questions cover a range of topics and are designed to provide a taste of the type of questions that may be encountered on the actual exam. By utilizing resources Certspots CIP Level 2 Certification NACE-CIP1-001 Demo Questions, individuals can better prepare themselves for the rigors of the exam and increase their chances of success.

Page 1 of 3

1. Which of these tests uses a syringe?

Sleeve test

Potassium ferricyanide

Bresle patch

Soluble salts meter

2. You ate the NACE Inspector on a job where NACE No. 2/SSPC - SP 10 has been specified. You are finding the Contractor is leaving mill scale on the on surface and as a result you have been rejecting the blast. The Contractor is very upset and has told you that the standard permits up to 5% of the mill scale to remain and still be in be in compliance with the standard.

Your FIRST preferred course of action is to:

Review the relevant standard with the Contractor

Permit coating to take place so as not to lose the blast

Call your supervisor

Shut the job down

3. The main responsibilities of the inspector are to

demonstrate to the contractor how to apply the coating.

observe and direct the work of the contractors.

direct and perform the work stated in the specification.

observe and report the quality of the work performed.

4. ISO SA 2 is defined as:

Near White Metal Blasting

Thorough Blast Cleaning

Very Thorough Blast Cleaning

Light Blast Cleaning

5. You are asked to be the only coating inspector on a small bridge recoating job where existing coating contains lead. The owners' representative has supplied you with the local code governing the removal and disposal of lead based coatings, however upon reading the document you having great deal of difficulty understanding the technical language.

As a NACE CIP Level 1 Inspector your preferred course of action is to:

Carefully review the document and do the best you can

Minimize your lack of understanding and go ahead with the inspection task to the best of your ability

Advise the owners’ representative of your lack of knowledge in this area

Hire a third patty to assist you in understanding the document

6. To achieve consistently accurate results with ALL alt test equipment

wear gloves when sampling.

wash your hands before sampling.

avoid placing the sample discs on a surface.

calibrate the instrument in the field.

7. Inspector's daily reports are used:

Select All That Apply

By the contractor to estimate the amount of work done that day

To provide continuity between inspectors

To aid in arbitration between the contractor and client

To help in cases of a coating failure

8. A single application coating film has a measured dry film thickness (DFT) between 4 and 5 mils (between 100 and 125 microns). The volume solids of the coating immediately before application were 67%,

What wet film thickness (WFT) was applied?

5 to 6 mils (125 to 150 microns)

10 to 12 mils (250 to 300 microns)

8 to 10 mils (200 to 250 microns)

6 to 7 mils (150 to 175 microns)

9. The initial steel condition is important to the NACE Inspector because:

If the steel is pitted more coating will be required

Less abrasive is need if the mill Scale s gone

It affects the final appearance after blasting

The Inspector may have to reject the Steel

10. NACE SP 0178 is a standard for:

Structural steel to be coated for Atmospheric Service

Tanks and Vessels to, be Lined for Immersion Service

Stainless steel pipe to be Externally Coated

Tanks and Vessels to be Externally Coated

Page 2 of 3

11. The NACE Inspector should perform tests for soluble salts:

Prior to surface preparation

After surface preparation

Prior to coating application

When specified

12. An exposed area of the substrate or previous coat of a conductive coating material, often caused by poor application technique is called

cracking.

sagging.

holiday.

checking.

13. The most important factor resulting in improved job site safety is:

Personal Protective Equipment

Engineering Controls

Safety Enforcement

Situational Awareness

14. The least effective method of surface cleaning is most likely

water blasting.

dry grit blasting.

hand tool cleaning.

power tool cleaning.

15. ISO SA 2.5 is defined as:

Near White Metal Blasting

Thorough Blast Cleaning

Very Thorough Blast Cleaning

Light Blast Cleaning

16. When performing tests for oil and grease using an ultra-violet light, the NACE Inspector should be aware that:

Chloride salt may produce a false positive

Synthetic oil or grease may not be identified

Ultra-Violet light may contaminant the surface

Presence of weld spatter may produce a false positive

17. Safety Data Sheets must be carefully reviewed by:

The Application personnel

The Inspection personnel

The Owner's personnel

All personnel involved in the job

18. Galvanic corrosion occurs on which of the following substrates:

Concrete

Fiberglass Reinforced Plastic

Metal

Wood

19. As a NACE Coating Inspector your responsibility with respect to safety is to:

Assume the role of the Safety Inspector

Check the PPE used by the Applicators

Act in accordance with the site safety requirements and set an example

Check the credentials of the Safety Officer on site

20. A magnetic pull-off type gauge is a good choice when:

Accuracy is not required

When an intrinsically safe tool is required

Performing an adhesion test

When working on non-ferrous metals

Page 3 of 3

21. An inspectors personal log book should contain:

Subjective comments re ding the application team

Objective comments regarding the application work

No comments regarding the application team

The inspector's personal opinions of the application team

22. Check abrasive blast pressure close to the

compressor

blast pot

blast nozzle

substrate

23. ASTM Standards are applicable:

In the USA

In North America

In Asia

When specified

24. What is used to determine compressed air cleanliness?

Needle pressure gauge

Psychrometer

Blotter test

Profilometer

25. Stripe coats are generally applied to:

Edges and corners

Welds

Complex geometric shapes

a), b), and c)

26. Excess moisture during holiday testing can cause erroneous indications by creating a path across the surface of the coating to pinholes previously detected, or directly to the signal return connection.

This is often referred to as:

telegraphing.

monitoring

juxtaposing.

transitioning.

27. When using a sling physchrometer a very large difference between the wet and dry bulb readings indicates:

High Relative Humidity

Low Relative Humidity

High Surface Temperature

Low Surface Temperature

28. Stripe coats are best applied by:

Airless spray

Conventional spray

High volume low pressure spray

Brush

29. If the project specification DOES NOT state the specific DFT measurement standards, the inspector should use

a recognized industry standard like SSPC-PA 2 that is broadly accepted

NACE 2/SSPC SP10

their best judgment based on similar projects and specifications.

a detailed checklist and document the lack of a standard.

30. When holiday testing is required the Inspector is always required to enforce NACE SP 0188:

True

False

By Jonnie Karnath NACE Free Dumps CIP Level 2 Certification, NACE-CIP1-001 Demo Questions, NACE-CIP1-001 dumps 0 Comments

Facebook Twitter LinkedIn Google + Email