Cisco 300-710 Dumps PDF Study Tips And Information 2023

Jonnie Karnath2023-03-21T14:02:47+00:00

Cisco 300-710 exam is a highly sought-after certification that can open doors to new job opportunities and career advancements. But passing the exam can be a challenge, especially if you’re not well-prepared. That’s where Certspot comes in with their Cisco 300-710 dumps PDF which are designed to help you prepare for the exam by providing you with a realistic testing experience. Cisco 300-710 dumps PDF are up-to-date, accurate, and designed to cover all the topics and concepts that you’ll need to know to pass the Securing Networks with Cisco Firepower (SNCF) exam. By studying Certspot’s Cisco 300-710 dumps PDF, you’ll be able to identify any knowledge gaps and focus your studying efforts on those areas, leading to a better chance of passing the exam.

Page 1 of 8

1. An engineer is configuring a second Cisco FMC as a standby device but is unable to register with the active unit.

What is causing this issue?

The primary FMC currently has devices connected to it.

The code versions running on the Cisco FMC devices are different

The licensing purchased does not include high availability

There is only 10 Mbps of bandwidth between the two devices.

2. An engineer installs a Cisco FTD device and wants to inspect traffic within the same subnet passing through a firewall and inspect traffic destined to the internet.

Which configuration will meet this requirement?

transparent firewall mode with IRB only

routed firewall mode with BVI and routed interfaces

transparent firewall mode with multiple BVIs

routed firewall mode with routed interfaces only

3. Refer to the exhibit.

A systems administrator conducts a connectivity test to their SCCM server from a host machine and gets no response from the server.

Which action ensures that the ping packets reach the destination and that the host receives replies?

Create an access control policy rule that allows ICMP traffic.

Configure a custom Snort signature to allow ICMP traffic after Inspection.

Modify the Snort rules to allow ICMP traffic.

Create an ICMP allow list and add the ICMP destination to remove it from the implicit deny list.

4. What must be implemented on Cisco Firepower to allow multiple logical devices on a single physical device to have access to external hosts?

Add at least two container instances from the same module.

Set up a cluster control link between all logical devices

Add one shared management interface on all logical devices.

Define VLAN subinterfaces for each logical device.

5. When a Cisco FTD device is configured in transparent firewall mode, on which two interface types can an IP address be configured? (Choose two.)

Diagnostic

EtherChannel

BVI

Physical

Subinterface

6. An engineer has been asked to show application usages automatically on a monthly basis and send the information to management.

What mechanism should be used to accomplish this task?

event viewer

reports

dashboards

context explorer

7. Which two types of objects are reusable and supported by Cisco FMC? (Choose two.)

dynamic key mapping objects that help link HTTP and HTTPS GET requests to Layer 7 application protocols.

reputation-based objects that represent Security Intelligence feeds and lists, application filters based on category and reputation, and file lists

network-based objects that represent IP address and networks, port/protocols pairs, VLAN tags, security zones, and origin/destination country

network-based objects that represent FQDN mappings and networks, port/protocol pairs, VXLAN tags, security zones and origin/destination country

reputation-based objects, such as URL categories

8. The administrator notices that there is malware present with an .exe extension and needs to verify if any of the systems on the network are running the executable file.

What must be configured within Cisco AMP for Endpoints to show this data?

prevalence

threat root cause

vulnerable software

file analysis

9. A security engineer must deploy a Cisco FTD appliance as a bump in the wire to detect intrusion events without disrupting the flow of network traffic.

Which two features must be configured to accomplish the task? (Choose two.)

inline set pair

transparent mode

tapemode

passive interfaces

bridged mode

10. Refer to the exhibit.

And engineer is analyzing the Attacks Risk Report and finds that there are over 300 instances of new operating systems being seen on the network.

How is the Firepower configuration updated to protect these new operating systems?

Cisco Firepower automatically updates the policies.

The administrator requests a Remediation Recommendation Report from Cisco Firepower

Cisco Firepower gives recommendations to update the policies.

The administrator manually updates the policies.

Page 2 of 8

11. An analyst using the security analyst account permissions is trying to view the Correlations Events Widget but is not able to access it. However, other dashboards are accessible.

Why is this occurring?

An API restriction within the Cisco FMC is preventing the widget from displaying.

The widget is configured to display only when active events are present.

The widget is not configured within the Cisco FM

The security analyst role does not have permission to view this widget.

12. A company wants a solution to aggregate the capacity of two Cisco FTD devices to make the best use of resources such as bandwidth and connections per second.

Which order of steps must be taken across the Cisco FTDs with Cisco FMC to meet this requirement?

Configure the Cisco FTD interfaces, add members to FMC, configure cluster members in FMC, and create cluster in Cisco FM

Add members to Cisco FMC, configure Cisco FTD interfaces in Cisco FM

configure cluster members in Cisco FMC, create cluster in Cisco FM

and configure cluster members in Cisco FM

Configure the Cisco FTD interfaces and cluster members, add members to Cisco FM

and create the cluster in Cisco FM

Add members to the Cisco FMC, configure Cisco FTD interfaces, create the cluster in Cisco FMC, and configure cluster members in Cisco FM

13. Refer to the exhibit.

An administrator is looking at some of the reporting capabilities for Cisco Firepower and noticed this section of the Network Risk report showing a lot of SSL activity that cloud be used for evasion.

Which action will mitigate this risk?

Use SSL decryption to analyze the packets.

Use encrypted traffic analytics to detect attacks

Use Cisco AMP for Endpoints to block all SSL connection

Use Cisco Tetration to track SSL connections to servers.

14. An engineer runs the command restore remote-manager-backup location 2.2.2.2 admin /Volume/home/admin FTD408566513.zip on a Cisco FMC. After connecting to the repository, the Cisco FTD device is unable to accept the backup file.

What is the reason for this failure?

The backup file is not in .cfg format.

The wrong IP address is used.

The backup file extension was changed from .tar to .zip.

The directory location is incorrect.

15. A Cisco FTD device is running in transparent firewall mode with a VTEP bridge group member ingress interface.

What must be considered by an engineer tasked with specifying a destination MAC address for a packet trace?

Only the UDP packet type is supported.

The output format option for the packet logs is unavailable.

The destination MAC address is optional if a VLAN ID value is entered.

The VLAN ID and destination MAC address are optional.

16. The event dashboard within the Cisco FMC has been inundated with low priority intrusion drop events, which are overshadowing high priority events. An engineer has been tasked with reviewing the policies and reducing the low priority events.

Which action should be configured to accomplish this task?

generate events

drop packet

drop connection

drop and generate

17. An engineer is attempting to add a new FTD device to their FMC behind a NAT device with a NAT ID of ACME001 and a password of Cisco388267669.

Which command set must be used in order to accomplish this?

configure manager add ACME001 <registration key> <FMC IP>

configure manager add <FMC IP> ACME0O1 <registration key>

configure manager add DONTRESOLVE <FMC IP> AMCE001 <registration key>

configure manager add <FMC IP> registration key> ACME001

18. An engineer is troubleshooting HTTP traffic to a web server using the packet capture tool on Cisco FMC. When reviewing the captures, the engineer notices that there are a lot of packets that are not sourced from or destined to the web server being captured.

How can the engineer reduce the strain of capturing packets for irrelevant traffic on the Cisco FTD device?

Use the host filter in the packet capture to capture traffic to or from a specific host.

Redirect the packet capture output to a .pcap file that can be opened with Wireshark.

Use the -c option to restrict the packet capture to only the first 100 packets.

Use an access-list within the packet capture to permit only HTTP traffic to and from the web server.

19. A network administrator configured a NAT policy that translates a public IP address to an internal web server IP address. An access policy has also been created that allows any source to reach the public IP address on port 80. The web server is still not reachable from the Internet on port 80.

Which configuration change is needed?

The intrusion policy must be disabled for port 80.

The access policy rule must be configured for the action trust.

The NAT policy must be modified to translate the source IP address as well as destination IP address.

The access policy must allow traffic to the internal web server IP address.

20. A network administrator is concerned about (he high number of malware files affecting users' machines.

What must be done within the access control policy in Cisco FMC to address this concern?

Create an intrusion policy and set the access control policy to block.

Create an intrusion policy and set the access control policy to allow.

Create a file policy and set the access control policy to allow.

Create a file policy and set the access control policy to block.

Page 3 of 8

21. An engineer is configuring a Cisco IPS to protect the network and wants to test a policy before deploying it. A copy of each incoming packet needs to be monitored while traffic flow remains constant.

Which IPS mode should be implemented to meet these requirements?

Inline tap

passive

transparent

routed

22. Network traffic coining from an organization's CEO must never be denied.

Which access control policy configuration option should be used if the deployment engineer is not permitted to create a rule to allow all traffic?

Configure firewall bypass.

Change the intrusion policy from security to balance.

Configure a trust policy for the CE

Create a NAT policy just for the CE

23. An engineer must configure a Cisco FMC dashboard in a child domain.

Which action must be taken so that the dashboard is visible to the parent domain?

Add a separate tab.

Adjust policy inheritance settings.

Add a separate widget.

Create a copy of the dashboard.

24. Remote users who connect via Cisco AnyConnect to the corporate network behind a Cisco FTD device report that they get no audio when calling between remote users using their softphones. These same users can call internal users on the corporate network without any issues.

What is the cause of this issue?

The hairpinning feature is not available on FT

Split tunneling is enabled for the Remote Access VPN on FTD

FTD has no NAT policy that allows outside to outside communication

The Enable Spoke to Spoke Connectivity through Hub option is not selected on FT

25. An engineer is setting up a remote access VPN on a Cisco FTD device and wants to define which traffic gets sent over the VPN tunnel.

Which named object type in Cisco FMC must be used to accomplish this task?

split tunnel

crypto map

access list

route map

26. With a recent summer time change, system logs are showing activity that occurred to be an hour behind real time.

Which action should be taken to resolve this issue?

Manually adjust the time to the correct hour on all managed devices

Configure the system clock settings to use NTP with Daylight Savings checked

Manually adjust the time to the correct hour on the Cisco FM

Configure the system clock settings to use NTP

27. An administrator is creating interface objects to better segment their network but is having trouble adding interfaces to the objects.

What is the reason for this failure?

The interfaces are being used for NAT for multiple networks.

The administrator is adding interfaces of multiple types.

The administrator is adding an interface that is in multiple zones.

The interfaces belong to multiple interface groups.

28. An engineer has been tasked with using Cisco FMC to determine if files being sent through the network are malware.

Which two configuration takes must be performed to achieve this file lookup? (Choose two.)

The Cisco FMC needs to include a SSL decryption policy.

The Cisco FMC needs to connect to the Cisco AMP for Endpoints service.

The Cisco FMC needs to connect to the Cisco ThreatGrid service directly for sandboxing.

The Cisco FMC needs to connect with the FireAMP Cloud.

The Cisco FMC needs to include a file inspection policy for malware lookup.

29. IT management is asking the network engineer to provide high-level summary statistics of the Cisco FTD appliance in the network. The business is approaching a peak season so the need to maintain business uptime is high.

Which report type should be used to gather this information?

Malware Report

Standard Report

SNMP Report

Risk Report

30. Which protocol is needed to exchange threat details in rapid threat containment on Cisco FMC?

SGT

SNMP v3

BFD

pxGrid

Page 4 of 8

31. A network engineer is extending a user segment through an FTD device for traffic inspection without creating another IP subnet How is this accomplished on an FTD device in routed mode?

by leveraging the ARP to direct traffic through the firewall

by assigning an inline set interface

by using a BVI and create a BVI IP address in the same subnet as the user segment

by bypassing protocol inspection by leveraging pre-filter rules

32. An engineer configures an access control rule that deploys file policy configurations to security zones or tunnel zones, and it causes the device to restart.

What is the reason for the restart?

Source or destination security zones in the access control rule matches the security zones that are associated with interfaces on the target devices.

The source tunnel zone in the rule does not match a tunnel zone that is assigned to a tunnel rule in the destination policy.

Source or destination security zones in the source tunnel zone do not match the security zones that are associated with interfaces on the target devices.

The source tunnel zone in the rule does not match a tunnel zone that is assigned to a tunnel rule in the source policy.

33. A network engineer is logged into the Cisco AMP for Endpoints console and sees a malicious verdict for an identified SHA-256 hash.

Which configuration is needed to mitigate this threat?

Add the hash to the simple custom deletion list.

Use regular expressions to block the malicious file.

Enable a personal firewall in the infected endpoint.

Add the hash from the infected endpoint to the network block list.

34. A network administrator is configuring Snort inspection policies and is seeing failed deployment messages in Cisco FMC.

What information should the administrator generate for Cisco TAC to help troubleshoot?

A "show tech" file for the device in question.

A "troubleshoot" file for the device in question.

A "troubleshoot" file for the Cisco FM

A "show tech" for the Cisco FM

35. An engineer is working on a LAN switch and has noticed that its network connection to the mime Cisco IPS has gone down Upon troubleshooting it is determined that the switch is working as expected.

What must have been implemented for this failure to occur?

The upstream router has a misconfigured routing protocol

Link-state propagation is enabled

The Cisco IPS has been configured to be in fail-open mode

The Cisco IPS is configured in detection mode

36. How many report templates does the Cisco Firepower Management Center support?

unlimited

37. An engineer must investigate a connectivity issue and decides to use the packet capture feature on Cisco FTD. The goal is to see the real packet going through the Cisco FTD device and see the Snort detection actions as a part of the output. After the capture-traffic command is issued, only the packets are displayed.

Which action resolves this issue?

Use the verbose option as a part of the capture-traffic command

Use the capture command and specify the trace option to get the required information.

Specify the trace using the -T option after the capture-traffic command.

Perform the trace within the Cisco FMC GUI instead of the Cisco FTD CL

38. Which process should be checked when troubleshooting registration issues between Cisco FMC and managed devices to verify that secure communication is occurring?

fpcollect

dhclient

sfmgr

sftunnel

39. What is the disadvantage of setting up a site-to-site VPN in a clustered-units environment?

VPN connections can be re-established only if the failed master unit recovers.

Smart License is required to maintain VPN connections simultaneously across all cluster units.

VPN connections must be re-established when a new master unit is elected.

Only established VPN connections are maintained when a new master unit is elected.

40. When creating a report template, how can the results be limited to show only the activity of a specific subnet?

Create a custom search in Firepower Management Center and select it in each section of the report.

Add an Input Parameter in the Advanced Settings of the report, and set the type to Network/I

Add a Table View section to the report with the Search field defined as the network in CIDR format.

Select IP Address as the X-Axis in each section of the report.

Page 5 of 8

41. A network administrator wants to block traffic to a known malware site at https://www.badsite.com and all subdomains while ensuring no packets from any internal client are sent to that site.

Which type of policy must the network administrator use to accomplish this goal?

Prefilter policy

SSL policy

DNS policy

Access Control policy with URL filtering

42. Which Cisco Firepower feature is used to reduce the number of events received in a period of time?

rate-limiting

suspending

correlation

thresholding

43. Due to an Increase in malicious events, a security engineer must generate a threat report to include intrusion events, malware events, and security intelligence events.

How Is this information collected in a single report?

Run the default Firepower report.

Export the Attacks Risk report.

Generate a malware report.

Create a Custom report.

44. An engineer configures a network discovery policy on Cisco FMC. Upon configuration, it is noticed that excessive and misleading events filing the database and overloading the Cisco FMC. A monitored NAT device is executing multiple updates of its operating system in a short period of time.

What configuration change must be made to alleviate this issue?

Leave default networks.

Change the method to TCP/SY

Increase the number of entries on the NAT device.

Exclude load balancers and NAT devices.

45. An administrator is adding a new URL-based category feed to the Cisco FMC for use within the policies. The intelligence source does not use STIX. but instead uses a .txt file format.

Which action ensures that regular updates are provided?

Add a URL source and select the flat file type within Cisco FM

Upload the .txt file and configure automatic updates using the embedded UR

Add a TAXII feed source and input the URL for the feed.

Convert the .txt file to STIX and upload it to the Cisco FM

46. With Cisco FTD integrated routing and bridging, which interface does the bridge group use to communicate with a routed interface?

switch virtual

bridge group member

bridge virtual

subinterface

47. What is the advantage of having Cisco Firepower devices send events to Cisco Threat Response via the security services exchange portal directly as opposed to using syslog?

All types of Cisco Firepower devices are supported.

An on-premises proxy server does not need to be set up and maintained.

Cisco Firepower devices do not need to be connected to the Internet.

Supports all devices that are running supported versions of Cisco Firepower.

48. A network administrator discovers that a user connected to a file server and downloaded a malware file. The Cisc FMC generated an alert for the malware event, however the user still remained connected.

Which Cisco APM file rule action within the Cisco FMC must be set to resolve this issue?

Detect Files

Malware Cloud Lookup

Local Malware Analysis

Reset Connection

49. Which two routing options are valid with Cisco FTD? (Choose Two)

BGPv6

ECMP with up to three equal cost paths across multiple interfaces

ECMP with up to three equal cost paths across a single interface

BGPv4 in transparent firewall mode

BGPv4 with nonstop forwarding

50. Which object type supports object overrides?

time range

security group tag

network object

DNS server group

Page 6 of 8

51. What are the minimum requirements to deploy a managed device inline?

inline interfaces, security zones, MTU, and mode

passive interface, MTU, and mode

inline interfaces, MTU, and mode

passive interface, security zone, MTU, and mode

52. An engineer wants to change an existing transparent Cisco FTD to routed mode.

The device controls traffic between two network segments.

Which action is mandatory to allow hosts to reestablish communication between these two segments after the change?

remove the existing dynamic routing protocol settings.

configure multiple BVIs to route between segments.

assign unique VLAN IDs to each firewall interface.

implement non-overlapping IP subnets on each segment.

53. Which two OSPF routing features are configured in Cisco FMC and propagated to Cisco FTD? (Choose two.)

OSPFv2 with IPv6 capabilities

virtual links

SHA authentication to OSPF packets

area boundary router type 1 LSA filtering

MD5 authentication to OSPF packets

54. An engineer is configuring multiple Cisco FTD appliances (or use in the network.

Which rule must the engineer follow while defining interface objects in Cisco FMC for use with interfaces across multiple devices?

An interface cannot belong to a security zone and an interface group

Interface groups can contain multiple interface types

Interface groups can contain interfaces from many devices.

Two security zones can contain the same interface

55. What is a feature of Cisco AMP private cloud?

It supports anonymized retrieval of threat intelligence

It supports security intelligence filtering.

It disables direct connections to the public cloud.

It performs dynamic analysis

56. Which command-line mode is supported from the Cisco Firepower Management Center CLI?

privileged

user

configuration

admin

57. A network administrator notices that inspection has been interrupted on all non-managed interfaces of a device.

What is the cause of this?

The value of the highest MTU assigned to any non-management interface was changed.

The value of the highest MSS assigned to any non-management interface was changed.

A passive interface was associated with a security zone.

Multiple inline interface pairs were added to the same inline interface.

58. What is the difference between inline and inline tap on Cisco Firepower?

Inline tap mode can send a copy of the traffic to another device.

Inline tap mode does full packet capture.

Inline mode cannot do SSL decryption.

Inline mode can drop malicious traffic.

59. Which two dynamic routing protocols are supported in Firepower Threat Defense without using FlexConfig? (Choose two.)

EIGRP

OSPF

static routing

IS-IS

BGP

60. When do you need the file-size command option during troubleshooting with packet capture?

when capture packets are less than 16 MB

when capture packets are restricted from the secondary memory

when capture packets exceed 10 GB

when capture packets exceed 32 MB

Page 7 of 8

61. An engineer must configure high availability for the Cisco Firepower devices. The current network topology does not allow for two devices to pass traffic concurrently.

How must the devices be implemented in this environment?

in active/active mode

in a cluster span EtherChannel

in active/passive mode

in cluster interface mode

62. With Cisco FTD software, which interface mode must be configured to passively receive traffic that passes through the appliance?

ERSPAN

IPS-only

firewall

tap

63. Which command is entered in the Cisco FMC CLI to generate a troubleshooting file?

show running-config

show tech-support chassis

system support diagnostic-cli

sudo sf_troubleshoot.pl

64. Which feature is supported by IRB on Cisco FTD devices?

redundant interface

dynamic routing protocol

EtherChannel interface

high-availability cluster

65. Which report template field format is available in Cisco FMC?

box lever chart

arrow chart

bar chart

benchmark chart

66. Which group within Cisco does the Threat Response team use for threat analysis and research?

Cisco Deep Analytics

OpenDNS Group

Cisco Network Response

Cisco Talos

67. Which two statements about deleting and re-adding a device to Cisco FMC are true? (Choose two.)

An option to re-apply NAT and VPN policies during registration is available, so users do not need to re-apply the policies after registration is completed.

Before re-adding the device in Cisco FMC, you must add the manager back in the device.

No option to delete and re-add a device is available in the Cisco FMC web interface.

The Cisco FMC web interface prompts users to re-apply access control policies.

No option to re-apply NAT and VPN policies during registration is available, so users need to re-apply the policies after registration is completed.

68. Which limitation applies to Cisco Firepower Management Center dashboards in a multidomain environment?

Child domains can view but not edit dashboards that originate from an ancestor domain.

Child domains have access to only a limited set of widgets from ancestor domains.

Only the administrator of the top ancestor domain can view dashboards.

Child domains cannot view dashboards that originate from an ancestor domain.

69. A mid-sized company is experiencing higher network bandwidth utilization due to a recent acquisition The network operations team is asked to scale up their one Cisco FTD appliance deployment to higher capacities due to the increased network bandwidth.

Which design option should be used to accomplish this goal?

Deploy multiple Cisco FTD appliances in firewall clustering mode to increase performance.

Deploy multiple Cisco FTD appliances using VPN load-balancing to scale performance.

Deploy multiple Cisco FTD HA pairs to increase performance

Deploy multiple Cisco FTD HA pairs in clustering mode to increase performance

70. 16.18.15, but the requestor asked for the engineer to open the port for all machines that have been trying to connect to it over the last week.

Which action must the engineer take to troubleshoot this issue?

Use the context explorer to see the application blocks by protocol.

Use the context explorer to see the destination port blocks

Filter the connection events by the source port 8699/udp.

Filter the connection events by the destination port 8699/udp.

Page 8 of 8

71. An administrator receives reports that users cannot access a cloud-hosted web server. The access control policy was recently updated with several new policy additions and URL filtering.

What must be done to troubleshoot the issue and restore access without sacrificing the organization's security posture?

Create a new access control policy rule to allow ports 80 and 443 to the FQDN of the web server.

Identify the blocked traffic in the Cisco FMC connection events to validate the block, and modify the policy to allow the traffic to the web server.

Verify the blocks using the packet capture tool and create a rule with the action monitor for the traffic.

Download a PCAP of the traffic attempts to verify the blocks and use the flexconfig objects to create a rule that allows only the required traffic to the destination server.

72. A network engineer is receiving reports of users randomly getting disconnected from their corporate applications which traverses the data center FTD appliance Network monitoring tools show that the FTD appliance utilization is peaking above 90% of total capacity.

What must be done in order to further analyze this issue?

Use the Packet Export feature to save data onto external drives

Use the Packet Capture feature to collect real-time network traffic

Use the Packet Tracer feature for traffic policy analysis

Use the Packet Analysis feature for capturing network data

73. A network administrator is troubleshooting access to a website hosted behind a Cisco FTD device External clients cannot access the web server via HTTPS The IP address configured on the web server is 192 168 7.46 The administrator is running the command capture CAP interface outside match ip any 192.168.7.46 255.255.255.255 but cannot see any traffic in the capture Why is this occurring?

The capture must use the public IP address of the web server.

The FTD has no route to the web server.

The access policy is blocking the traffic.

The packet capture shows only blocked traffic

74. A security engineer needs to configure a network discovery policy on a Cisco FMC appliance and prevent excessive network discovery events from overloading the FMC database?

Which action must be taken to accomplish this task?

Change the network discovery method to TCP/SY

Configure NetFlow exporters for monitored networks.

Monitor only the default IPv4 and IPv6 network ranges.

Exclude load balancers and NAT devices in the policy.

75. An engineer is restoring a Cisco FTD configuration from a remote backup using the command restore remote-manager-backup location 1.1.1.1 admin /volume/home/admin BACKUP_Cisc394602314.zip on a Cisco FMG. After connecting to the repository, an error occurred that prevents the FTD device from accepting the backup file.

What is the problem?

The backup file is not in .cfg format.

The backup file is too large for the Cisco FTD device

The backup file extension was changed from tar to zip

The backup file was not enabled prior to being applied

76. Which CLI command is used to control special handling of clientHello messages?

system support ssl-client-hello-tuning

system support ssl-client-hello-display

system support ssl-client-hello-force-reset

system support ssl-client-hello-reset

77. DRAG DROP

Drag and drop the steps to restore an automatic device registration failure on the standby Cisco FMC from the left into the correct order on the right. Not all options are used.

Facebook Twitter LinkedIn Google + Email